Fabricate two L-shaped brackets from 1.25a€? x 3/16a€? metallic. The brackets had been 7.5 in longer. I dona€™t has a bender, and so I welded the perspective on. I needed a good fold, and bending they in a vice woulda€™ve produced too-large a radius. In hindsight I probably could’ve achieved this with just bending plus curves. These brackets will bolt aside in the slider action layer steel. The brackets tend to be secured with two 1a€? x 3/8a€? level 8 bolts, washers, van sheet-metal, locking crazy, anti-seize substance. I did sona€™t see a need for backing plates here as the main load is absolute.
Fabricate two Z shaped brackets out of 1.25a€? x 3/16a€? metallic. These brackets had been furthermore 7.5 in lengthy total. These will bolt on the underside on the floor in the van. To decrease the possibility of tearout or bending the floor in any sort of accident, I fabricated some support plates 3 ins lengthy a€“ in essence actually larger washers. Both of these brackets were secured with 1.5a€? x 7/16a€? grade 8 screws, supporting dishes, van sheet-metal, a washer to level out sheet-metal within the van, a locking fan, and anti-seize composite.
Prime and painting the hardware. I used rust oleum automobile muscles black primer, and plutonium black paint and clearcoat. The plutonium are interesting stuff a€“ keeps a dry period of less than six mins, therefore the full paint process took around an hour and fifteen minutes for one coat of primer, single layer of pigment, and unmarried clearcoat.
Test fit the system. Test fitted indicated that the regulator wouldn’t normally clear the van framework and whole container must be moved inboard about 1 inch. In addition needed to lower the height regarding the regulator set-up, so I changed a-1 inch nipple with an in depth breast. We got rid of the brackets, caught all of them in a vice and pounded curve into these to accomplish the change. This dinged upwards my paint, but oh well.
Install the container. Test the match once again. Now You will find approximately half an inch of approval between the regulator in addition to structure. I could become a wrench on any the fixtures I need to change after if necessary. Discover a cross frame representative right holding the guts portion of the tank, which enhances the rigidity for this construction. General they feels totally bomber.
Path the trunk propane line from backside with the tank, on the exhaust range, and end in the extended framework representative simply on the other hand on the gas tank. Shield this portion of the run because of the half-inch heatshield.
Route the feeder range for kitchen stove along the framing associate, crossing-over into beyond the van nearby the gas tank refill, passing up inside interior wall surface associated with the van through the massive 4 x 6 beginning inside the B pillar
Route the feeder range for all the water heater straight across the van while watching backside controls better, through a hole inside section of the wall, and up inside interior.
Secure all contours with half-inch stainless pipe clamps, 1/4a€? stainless screws and washers, and 1/4a€? plus crazy. I use current holes for the framework in which feasible, in addition to several 8 mm threaded gaps.
Purge the tank on local propane supplier.
Test for leakage by opening the solenoid, after that closing and monitoring the pressure determine.
We have temperature shielding about propane range where it passes by on top of the fatigue system, but I’m still examining the necessity for shielding on container alone. We ran the van hot for one hour and mightn’t obtain the surface of the container go over background heat, but i shall retest in the summer and either increase temperature shielding into tank or continue the fatigue system heatshield.
Construction area
Preparation where the container should match. We ended up installing it more forward that i needed considering that the distance involving the front and back regarding the container harmonized best using step sheet metal only at that area – although onward side of the tank is more subjected to the fatigue system. I really don’t envision it should be something.
Container and its equipment
Beginning with the 
tank a€“ POL valve, T, reliable container attachment fitting, outdoor bbq installing, solenoid, stress determine, 2 period regulator, support bracket. The Manchester tank amount measure is located at the lower left, while the fill port utilizing the yellowish limit is within the heart.