Posted on by Steven Helgoth

It is the intention with this document to furnish users of standard steel structures with practical information about a method that is acceptable planning structures for 4-1/2″, 5″ or constant electric hinges.

It is the intention with this document to furnish users of standard steel structures with practical information about a method that is acceptable planning structures for 4-1/2″, 5″ or constant electric hinges.

Electronic Hinge Preparations

1 Function

This document allows framework manufacturers to offer frames ahead of having familiarity with the particular electric https://datingmentor.org/loveroulette-review/ hinge being utilized.

2 Scope

The information included herein relates to frames stated in accordance with ANSI A250.8. The planning as defined herein will accommodate nearly all electric hinges sold. It is the responsibility of this hardware specifier to assure hinges that are compatible utilized.

3 Guide Documents

ANSI/SDI A250.6 suggested Practice for Hardware Reinforcings on Standard Steel D rs and Frames

ANSI/BHMA A156.7 Template Hinge Dimensions

ANSI/BHMA A156.115 Hardware Preparation in Metal D rs and Metal Frames

4 Tolerances

All values that do not carry certain tolerances or are perhaps not marked maximum or minimum shall have the following tolerances Linear proportions shall be В± 1/16 in. (1.6 mm). Weight or force shall be В± 2%. Angles shall be В± 2 levels. Where only minus tolerances are given, the dimensions are permitted to be exceeded at the option associated with the manufacturers.

5 Location

The preparation for electric hinges will be non-load bearing. In order that it shall be found in the center hinge preparation on structures with 1-1/2 pair of hinges, and on the second hinge from the underside on frames with 2 pair of hinges.

6 Hinge Reinforcement

The hinge reinforcement shall conform to ANSI A250.6 and ANSI A250.8, and shall incorporate cutouts as shown in numbers 1, 2, 3 and 4.

7 Junction Box

A junction field can be provided to facilitate wiring and connector installation. In addition, a gap will probably be supplied at the top and bottom associated with junction box to enhance conduit (see Figure 4). It’s the responsibility for the electrical contractor to connect any unused holes.

Figure 1 – Preparation of 1 3/4″ Steel D rs & Frames for 5″ complete Mortise Electrical Hinge

Note 1 The hinge backset on the home differs by hollow metal d r manufactures from 3/16″ to 1/4″.

Note 2 The hinge backset regarding the framework varies by hollow metal framework manufactures from 5/16″ to 3/8″.

Note 3 Extra holes may possibly occur into the reinforcement for installation and t ling fixturing.

Note 4 Some manufacturers give you a detachable feature (e.g. – wire, shim, standoff projection) to allow transformation of the standard fat planning to be used with heavy fat hinge butt.

Note 5 probably the most typical mortise depths come in conformity with ANSI/BHMA A156.1 as follows

  • Standard Weight butt 0.146″
  • Heavy weight butt 0.190″

Figure 2 – Preparation of 1 3/4″ Steel D rs & Frames for 4 1/2 Full Mortise Electric that is″ Hinge

Note 1 The hinge backset on the home varies by hollow metal d r manufactures from 3/16″ to 1/4″ whenever hinge filler is set up.

Note 2 The hinge backset in the frame varies by hollow metal framework manufactures from 5/16″ to 3/8″

Note 3 additional holes might occur within the reinforcement for installation and t ling fixturing.

Note 4 Some manufacturers give you a removable feature (e.g. – wire, shim, standoff projection) to permit transformation of a standard weight planning for use with hefty weight hinge butt.

Note 5 The most typical mortise depths come in conformity with ANSI/BHMA A156.1 as follows

  • Standard Weight butt 0.134″
  • Heavy weight butt 0.180″

Figure 3 – Preparation of 1 3/4″ Steel D rs & Frames for 4 1/2 ″ Comprehensive Mortise Electric Hinge Non-handed

Note 1 The hinge backset in the d r varies by hollow metal d r manufactures from 3/16″ to 1/4″ whenever hinge filler is set up.

Note 2 The hinge backset in the framework differs by hollow metal framework manufactures from 5/16″ to 3/8″

Note 3 Extra holes might occur in the reinforcement for t ling and installation fixturing.

Note 4 Some manufacturers give you a detachable feature (e.g. – wire, shim, standoff projection) allowing conversion of a standard weight planning for use with hefty weight hinge butt.

Note 5 The most mortise that is common are in accordance with ANSI/BHMA A156.1 as follows

  • Standard Body Weight butt 0.134″
  • Hefty fat butt 0.180″